The Tesla coil
Level 29
This walkthrough shows once you unlock the level.
An electrician's lecture is laid out on the slate table. At the left stands a Wimshurst machine: two glass discs with tinfoil sectors, a crank at its foot, and two brass rods with balls over the discs. A gold-leaf electroscope stands behind it. A mahogany case with a glazed lid stands at the front left. In the middle stands a mahogany cabinet with a slate spark board in its front and a Tesla coil on its top, with a copper spiral round its foot, four empty jar sockets under a brass bar, a small ivory dial and three little bells. A faint violet glow hangs round the brass sphere on top of the coil and grows brighter with each mechanism you finish. At the right stands a stand of glowing tubes with six lever switches, an induction coil and a lecture bill on a wing, and a bottle of orange liquid beside it.
Two chains of steps run side by side. The machine, the case, the jars and the spark board make one. The bottle and the tubes make the other, and the tubes need the spare tube from the case. The coil comes last. The machine's crank, the electroscope's knob, the bells, the radiometer at the front right, the knife switch at the front and the drum switch on the induction coil all move but open nothing. The crank is still the part that charges the machine and the jars.
The machine
- Look at the front disc. A brass bar with a tinsel brush at each end lies level across it. Behind it on the axle is a small brass stop with a notch, set at 45°.
- Drag the bar round, or tap it. It drops into the stop's notch with a click, and its brushes touch the sectors.
- Look through the glass, or orbit behind the machine. The back disc has its own bar and its own stop, at 45° the other way. Drag or tap that bar too. The two bars now cross at a right angle.
- Look at the top. The two brass balls touch, so no spark can cross between them. Drag the black handle on the right rod, or tap it. The rod swings out and leaves a gap of a few centimetres. A second tap swings it back.
- Turn the crank at the foot of the machine by dragging it round, or tap it for one whole turn. The discs turn opposite ways and the brushes glow violet. The electroscope's gold leaves spread as the charge builds.
- After a few turns a spark cracks across the gap. With a bar off its stop the leaves barely move and no spark comes. With the balls touching nothing builds at all.
The case
- Tap the brass hook on the front of the case. It swings up off the eye on the lid. While the hook is on, a tap on the lid only rattles it.
- Tap the lid. It swings up on its hinges at the back.
- Tap the discharging tongs in the lid's leather strap, the wire tray of four Leyden jars and the glass tube in the velvet groove at the front. Each goes into the satchel.
The jars
- A brass chain hangs from the machine's right rod to a peg on the cabinet's left side. Tap the hook on the peg. The chain lifts onto the brass post at the left end of the bar over the empty sockets.
- Tap the four empty sockets with the tray of jars in the satchel. The jars drop in one after another, and the bar's springs press on their knobs.
- The machine must be working: both bars on their stops and the balls apart, as in the first section.
- Turn the machine's crank. The pith ball on the ivory dial at the right end of the bar rises with each turn. When it stands straight out to the right at the end of its scale, the jars are charged.
The spark board
The board has a brass ball at the left, wired to the jars, and a brass ball at the right, wired to the coil. Two brass studs on green wires are earths. Four brass knobs on glass stems each slide in a slot with five brass notch marks. The brass rule on the top rail, between two small balls, is the longest leap a spark can make.
The rule: from the left ball the spark leaps to the nearest knob, earth stud or right ball that it has not touched yet, as long as that one is no further away than the length of the brass rule. It goes on from there by the same rule.
- Drag a knob along its slot. It settles on the nearest notch. A tap steps it one notch along, and back again from the end of the slot.
- Tap the left ball. The tongs from the satchel touch it, and the jars fire a spark across the board, with a crack at each leap.
- Watch where the spark ends. A flash at an earth stud means that stud was nearer than the next knob. A hissing violet glow on a knob means nothing lay within the brass rule's length. A fork means two things lay at the same distance. A spark that reaches the right ball with dark knobs behind it has skipped them, and the coil only buzzes.
- Method: work from the left ball. Place the first knob so it is nearer to the left ball than anything else and within the rule's length. Then place the second knob so it is the nearest thing to the first, and nearer than the earth studs, the later knobs and the right ball. Go on to the last knob, which must be nearer to the right ball than anything else is. Fire after each change to see how far the spark gets.
- When the spark leaps all four knobs into the right ball, the coil hums and a short streamer flicks from its sphere.
The tubes
- Look at the bottle beside the stand. Its zinc plate hangs above the orange liquid on a brass rod. Tap the thumbscrew in the bottle's black cap to loosen it.
- Drag the rod's knob down, or tap it. The zinc sinks into the liquid, bubbles rise and the hammer at the end of the induction coil buzzes.
- One pair of clips on the board is empty. Tap them with the spare tube from the satchel. It snaps in.
- Read the bill on the wing at the right of the stand. It shows the six numbered terminals and the tubes between them. The tubes painted in colour must glow. The tubes drawn grey must stay dark.
- Each lever switch on the base carries the number of its terminal. A tap moves it from the middle to the red stud, then to the black stud, then back to the middle.
- The rule: a tube glows when one of its terminals is on a red stud and the other on a black stud. A terminal in the middle is cut off, so none of its tubes glow. A tube glows brightest at its black end.
- Method: pick a terminal at the end of a bill tube and set it to red. Set every terminal joined to it by a bill tube to black, then every terminal joined to those by a bill tube to red, and so on. Two terminals joined by a grey tube must not be one red and one black. A terminal that has no bill tube goes to the middle when it is joined by grey tubes to both a red and a black terminal. When only the bill's tubes glow, the levers lock with a click.
The coil
- On the cabinet's right side, the copper blade of a knife switch stands out. A brass pin through a staple holds it. Tap the pin. It pulls out and hangs on its chain.
- A brass clip on a braided lead sits on the copper spiral round the coil's foot. Drag it along the spiral toward the coil or away, or tap it to step it one turn at a time.
- Tap the switch's black handle. The blade snaps into its jaws and the coil fires for two seconds, then the blade springs out again.
- Before the spark board is passed and the tubes are lit, the coil only buzzes. After that, streamers leap from the brass sphere on its top. Their length shows how near the clip is to the turn that tunes the coil, which changes each game. One turn away they are short, two turns away they hardly show.
- Move the clip a turn and fire again until the streamers are longest. When the coil fires at the tuned turn, the room goes dark and the lecture's last experiment begins: the coil throws streamers into the air and every tube on the stand glows without a wire.